<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2800.1400" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV><FONT face=Arial size=2>Hi all,</FONT></DIV>
<DIV><FONT face=Arial size=2>mir scheint, ich habe ein ähnlich gelagertes
Problem wie Christian (b1-PCI und Kernel 2.6.1) nur sollte das doch im 2.6.7
Kernel schon längst mit drin sein? Hier die Info´s, die ich habe:</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>lsmod | grep
capi<BR>capidrv
26805 0<BR>isdn
129697 1
capidrv<BR>capi
13441 0<BR>capifs
4041 2
capi<BR>kernelcapi
39393 5
capidrv,capi,b1pci,b1dma,b1<BR></FONT></DIV>
<DIV><FONT face=Arial size=2>lsmod | grep
b1<BR>b1pci
7757
0<BR>b1dma
14701 1
b1pci<BR>b1
22093 2
b1pci,b1dma<BR>kernelcapi
39393 5
capidrv,capi,b1pci,b1dma,b1</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>dmesg (nach dem booten)</FONT></DIV>
<DIV><FONT face=Arial size=2>...</FONT></DIV>
<DIV><FONT face=Arial size=2>CAPI Subsystem Rev 1.1.2.8<BR>b1: revision
1.1.2.2<BR>b1dma: revision 1.1.2.3<BR>ACPI: PCI interrupt 0000:02:02.0[A] ->
GSI 9 (level, low) -> IRQ 9<BR>b1pci: PCI BIOS reports AVM-B1 at i/o 0xa800,
irq 9<BR>kcapi: Controller 1: b1pci-a800 attached<BR>b1pci: AVM B1 PCI at i/o
0xa800, irq 9, revision 2<BR>b1pci: revision 1.1.2.2<BR>divert: freeing
divert_blk for eth0<BR>kcapi: Controller 1: b1pci-a800
unregistered<BR>...</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>lade ich die Module mit der "Hand" bekomme ich
unter dmesg folgenden Eintrag:</FONT></DIV>
<DIV><FONT face=Arial size=2>....</FONT></DIV>
<DIV><FONT face=Arial size=2>CAPI Subsystem Rev 1.1.2.8<BR>b1: revision
1.1.2.2<BR>b1dma: revision 1.1.2.3<BR>ACPI: PCI interrupt 0000:02:02.0[A] ->
GSI 9 (level, low) -> IRQ 9<BR>b1pci: PCI BIOS reports AVM-B1 at i/o 0xa800,
irq 9<BR>kcapi: Controller 1: b1pci-a800 attached<BR>b1pci: AVM B1 PCI at i/o
0xa800, irq 9, revision 2<BR>b1pci: revision 1.1.2.2<BR>capifs: Rev
1.1.2.3<BR>capi20: Rev 1.1.2.7: started up with major 68
(middleware+capifs)<BR>CSLIP: code copyright 1989 Regents of the University of
California<BR>ISDN subsystem Rev:
1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded<BR>capidrv: Rev 1.1.2.2:
loaded<BR></DIV>
<DIV>aber trotzdem funktioniert die B1 nicht. Das laden der Firmware crashed das
gesamte System</DIV>
<DIV> </DIV>
<DIV>capiinit start<BR>ERROR: cannot load module kernelcapi<BR></DIV>
<DIV>capiinfo</DIV>
<DIV>capi not installed - No such device or address (6)</DIV>
<DIV> </DIV>
<DIV>cat /proc/capi/controller</DIV>
<DIV>1 b1pci detected
b1pci-a800 - - 0xa800 9 r2</DIV>
<DIV> </DIV>
<DIV>cat /proc/capi/controllers/1</DIV>
<DIV>name
b1pci-a800<BR>io
0xa800<BR>irq
9<BR>type
B1 PCI<BR>cardname<BR></DIV>
<DIV>Kann mir bitte jemand helfen, warum die Kiste nicht läuft, ich versteh so
langsam nichts mehr. </DIV>
<DIV>Die Kernel src Doku hab ich bereits durch :-( und auch google hab ich
durch</DIV>
<DIV>Gruß aus München</DIV>
<DIV>Bernd</DIV>
<DIV> </DIV></FONT></BODY></HTML>
<HTML>__________________________________________________<br><br>This message has been scanned by F-Secure Anti-Virus for Microsoft Exchange.</HTML>