linux-avmb1:Problems with sending faxes with c2faxsend
linux at xolphin.nl
linux at xolphin.nl
Mon Jun 14 01:20:02 CEST 2004
[Sent to both the linux-avmb1 as the Hylafax mailinglist]
Hi,
I have some problems with sending faxes with Fedora, Hylafax and my AVM B1
controller. Receiving faxes works without any problems. c2faxsend does try
to sent a fax, but it terminates again within a second. I found various
other people having the exact same problems, discussed in for example
http://www.kofler.cc/forum/forumthread.php?rootID=2719#2827. I have been
using the controller without any problems for almost two years now with the
same configuration, but to due a harddisk failure I had to reinstall my
complete machine. Fortunatly I had a backup of all the configuration and
data files, but that didn't include the driver and program stuff.
I have the following configuration:
Environment: Fedora Core 2
Kernel: Kernel 2.6.6
Hylafax: 4.1.8
Capi4Hylafax: 01.02.02 (from ftp.avm.de)
Capi4kutils: 2004-03-31 (from ftp.in-berlin.de)
Fax-number: +31 72 5648905
My config.faxCAPI:
SpoolDir: /var/spool/hylafax
FaxRcvdCmd: /var/spool/hylafax/bin/faxrcvd
PollRcvdCmd: /var/spool/hylafax/bin/pollrcvd
FaxReceiveUser: uucp
LogFile: /var/spool/hylafax/log/capi.log
LogTraceLevel: 0
LogFileMode: 0666
{
HylafaxDeviceName: faxCAPI
RecvFileMode: 0666
FAXNumber: +31.72.5648905
LocalIdentifier: "Xolphin"
MaxConcurrentRecvs: 2
OutgoingController: 1
OutgoingMSN: 5648905
SuppressMSN: 0
NumberPrefix:
UseISDNFaxService: 0
RingingDuration: 0
{
Controller: 1
AcceptSpeech: 1
UseDDI: 0
DDIOffset:
DDILength: 0
IncomingDDIs:
IncomingMSNs: 5648905
AcceptGlobalCall: 1
}
}
Permissions and stuff are set correctly. I tried other setups (kernel 2.4,
mungo.homelinux.org rpm's, mISDN, isdn4k-utils) too, but without any
success.
When I start the capi environment by executing 'capiinit start' I get the
following error in /var/log/messages (this was introduced while I was
debugging my problem, however I don't know how to get rid of it again):
capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
b1: revision 1.1.2.2
b1dma: revision 1.1.2.3
PCI: Found IRQ 10 for device 0000:00:0b.0
b1pci: PCI BIOS reports AVM-B1 V4 at i/o 0xd800, irq 10, mem 0xe0001000
kcapi: Controller 1: b1pciv4-d800 attached
b1pci: AVM B1 PCI V4 at i/o 0xd800, irq 10, mem 0xe0001000, revision 4 (dma)
b1pci: revision 1.1.2.2
b1pciv4-d800: card 1 "B1" ready.
b1pciv4-d800: card 1 Protocol: DSS1
b1pciv4-d800: card 1 Linetype: point to multipoint
b1pciv4-d800: B1-card (3.11-03) now active
Debug: sleeping function called from invalid context at
include/asm/semaphore.h:119
in_atomic():1, irqs_disabled():0
Call Trace:
[<0211691d>] __might_sleep+0x80/0x8a
[<1a8fd3d6>] capi_ctr_ready+0x22/0xa3 [kernelcapi]
[<1a90f01b>] b1dma_handle_rx+0x531/0x6b0 [b1dma]
[<1a90f22d>] b1dma_handle_interrupt+0x93/0xf3 [b1dma]
[<1a90f294>] b1dma_interrupt+0x7/0xd [b1dma]
[<0210707e>] handle_IRQ_event+0x28/0x48
[<02107311>] do_IRQ+0xf3/0x169
=======================
[<0210403b>] default_idle+0x23/0x26
[<02112590>] apm_cpu_idle+0xe4/0x121
[<0210408c>] cpu_idle+0x1f/0x34
[<02318612>] start_kernel+0x174/0x176
kcapi: card 1 "b1pciv4-d800" ready.
Everything seems to work alright, with the exception of sending faxes with
c2faxsend or Hylafax. Sending faxes with capisuite however isn't a problem (
I only don't want to use capisuite due the lack of a good Windows based
printing system (like for example http://winprinthylafax.sourceforge.net/)).
When I try to fax a fax with "c2faxsend -d 5648905 -f TIFF sendq/test.tif"
in the HylaFax directory I get the following message:
> Try to connect to fax number 5648905 in TIFF mode on controller 1.
> Dial and starting transfer of TIFF-File /var/spool/sendq/test.tif with
normal resolution.
The command is completed within a second (my phone rings only once (and I
tried my normal phone, and my cellular too)).
I did make a debug built, to find the exact problem, and this resulted in
the following message printed out:
CFaxSend - Constructor<
>CFaxSend - Constructor
CFaxSend::Config<
(/var/spool/hylafax/etc/config.faxCAPI,1,6)<
>CFaxSend::Config
Fax-File=sendq/test.tif
CFaxSend::Send<
(5648905,0,0)<
LogFile=8f372a0-/var/spool/hylafax/log/capifax.log
CFaxSend::WriteLog<
>CFaxSend::WriteLog
CFaxSend::WriteLog<
>CFaxSend::WriteLog
CapiTrace: CAPI_REGISTER Success
CapiTrace: CONNECT_REQ(1)
>(0)>CFaxSend::Send
CapiTrace: CONNECT_CONF(101)
fs.exitState=a
CFaxSend - Destructor<
>CFaxSend - Destructor
[assertion failed: (CurState() == cs_Released) in Channel.cpp(82)]
[assertion failed: (GetState() == cs_Released) in CapiChan.cpp(85)]
[assertion failed: (GetPLCI() == IllegalPLCI) in CapiChan.cpp(86)]
[warning: (GetInitiator() == vFalse) in CapiChan.cpp(88)]
[assertion failed: (m_hCapiBase == vIllegalHandle) in CapiMsg.cpp(97)]
[assertion failed: (GetApplID() == IllegalApplID) in CapiMsg.cpp(98)]
[assertion failed: (m_RegisterState == REGISTER_STATE_RELEASED) in
CapiMsg.cpp(101)]
>CFaxSend-main
Sending faxes from Hylafax itself results in the following message:
> Your facsimile job to 5648905 was not sent because:
> An error occured while trying to establish the connection.
> The job will be retried at 20:11.
> ---- Transcript of session follows ----
>
> Jun 13 20:06:07.91: [ 3193]: SESSION BEGIN 00000003 +31.72.5648905 Jun 13
20:06:07.91: [ 3193]: FAX FAX: JOB 3 DEST 5648905 COMMID 00000023 Jun 13
20:06:07.91: [ 3193]: Try to connect to fax number 5648905 in Hylafax mode
on controller 1.
> Jun 13 20:06:07.91: [ 3193]: Dial and starting transfer of TIFF-File
docq/doc3.ps;31 with fine resolution.
> Jun 13 20:06:08.91: [ 3193]: SESSION END
I have been debuggin this problem for several days now, but I can't find any
solution at all. I already contacted AVM about this but they are just saying
"We are very sorry, but we only support Suse".
Is there anyone that knows how to solve this irritating bug? I hope to hear
from you!
Kind regards,
Maarten Bremer
More information about the linux-avmb1
mailing list