linux-avmb1:AVM ISDN Fritz Card, Hylafax, capi4hylafax and QualifyTSI, QualifyCID and QaulifyCNAME
Lívio Cipriano
lcipriano at iol.pt
Fri Jul 7 11:10:06 CEST 2006
Hi,
I'm using a AVM ISDN Fritz Card (2003), with SuSE Linux 9.2, Hylafax and
CAPI4Hylafax 4.2.0-5., and my config filers are:
CONFIG
-------------------------------------------------------------------
LogFacility: daemon
CountryCode: 351
AreaCode: 1
LongDistancePrefix: 1
InternationalPrefix: 00
DialStringRules: "etc/dialrules"
ServerTracing: 1
SessionTracing: 0xffffffff
MaxConcurrentCalls: 2
MaxSendPages: 1024
ModemGroup: any:.*
SendFaxCmd: /var/spool/fax/bin/faxsend
CONFIG.faxCAPI
------------------------------------------------------------------
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
# Grunds�zliches:
# - Es gibt fr jeden Wert einen Standardzustand (default), sodass jede Zeile
# der Datei oder auch das komplette Configfile ausgelassen werden kann.
# - Es gibt ausschlie�ich ein Configfile, in dem alle n�igen Angaben fr
# "c2faxsend/-receive" eingetragen werden k�nen.
# - Werden fr HylaFAX mehrere virtuelle Ger�e (devices) angelegt, muss es
# fr jedes Device ein Configfile im Format config.[DeviceName] geben.
# Dessen Existenz wird von HylaFAX berprft. Ohne dieses File kann die
# Arbeit mit dem Device nicht aufgenommen werden. Die Existenz einer
# solchen Datei kann am einfachsten durch einen Link auf dieses ConfigFile
# oder ein minimales "dummy"-ConfigFile nachgewiesen werden.
#
# Basics:
# - There is a default condition for each value, such that each line of the
# file or the complete configfile can be left out.
# - There is only one configfile in which all information required for
# "c2faxsend/-receive" can be entered.
# - If multiple virtual devices are created for HylaFAX, there must be a
# Configfile in the format config.[DeviceName] for each device. HylaFAX
# checks that this file exists. Without this file, it is not possible to
# start working with the device. The easiest way to establish the existence
# of such a file is to create a link to this ConfigFile or a minimum
# "dummy" ConfigFile.
# "SpoolDir" gibt den Pfad an, unter dem im HylaFAX-kompatiblen Betrieb die
# HylaFAX-Dateien zu finden sind oder unter dem im Stand-Alone-Betrieb die
# empfangenen Faxe gespeichert werden sollen. Im HylaFAX-kompatiblen Betrieb
# werden die Faxe im Verzeichnis $(SpoolDir)/recvq gespeichert.
#
# "SpoolDir" indicates the path in which the HylaFAX are located in HylaFAX-
# compatible operation or in which received faxes are to be saved in
# stand-alone operation. In HylaFAX-compatible operation, faxes are saved in
# the directory $(SpoolDir)/recvq.
#
# default /var/spool/fax
#
SpoolDir: /var/spool/fax
# "FaxRcvdCmd" gibt das Skript an, das ausgefhrt wird, sobald ein Fax
# empfangen wurde. Im Stand-Alone-Betrieb werden andere Parameter
# bergeben als fr HylaFAX (mehr dazu im sample_faxrcvd).
#
# "FaxRcvdCmd" indicates the script performed whenever a fax is
# received. Parameters other than the ones for HylaFAX are returned in
# stand-alone operation (see sample_faxrcvd for more information).
#
# default /var/spool/hylafax/bin/faxrcvd
#
FaxRcvdCmd: /var/spool/fax/bin/faxrcvd
# "PollRcvdCmd" gibt das Skript an, das ausgefhrt wird, sobald ein
# Fax per Faxabruf empfangen wurde. Im Stand-Alone-Betrieb werden
# andereParameter bergeben als fr HylaFAX (mehr dazu im
# sample_faxrcvd).
#
# "PollRcvdCmd" indicates the script performed whenever a fax was
# received by fax polling. Parameters other than the ones for HylaFAX
# are returned in stand-alone operation (see sample_faxrcvd for more
# information).
#
# default /var/spool/hylafax/bin/pollrcvd
#
PollRcvdCmd: /var/spool/fax/bin/pollrcvd
# "FaxReceiveUser" ist der User, als der c2faxrecv ausgefhrt wird.
# Die �derung des Users kann nur vom Superuser bzw. "root" erfolgen. Sollte
# c2faxrecv von einem anderen User gestartet werden, wird dieser Eintrag
# ignoriert. Hier einen anderen als den Hylafax-Standardwert "fax"
# einzutragen ist dann sinnvoll, wenn beispielsweise die Rechte von
# /dev/capi20 nicht ge�dert werden sollen oder Ihre Linux-Distribution einen
# anderen User voraussetzt.
#
# "FaxReceiveUser" is the user when c2faxrecv is run. This user can be
# changed only by the Superuser or "root" user. If c2faxrecv is started by
# another user, this entry will be ignored. Here it is a good idea to enter a
# value other than the hylafax default value "fax", for instance, if the
# rights of /dev/capi20 are not to be changed or your Linux distribution
# requires another user.
#
# default ""
#
FaxReceiveUser: root #fax
# "FaxReceiveGroup" ist die Gruppe, als die c2faxrecv ausgefhrt wird.
# Hier einen anderen als den Hylafax-Standardwert "uucp" einzutragen
# ist dann sinnvoll, wenn beispielsweise die Rechte von /dev/capi20 nicht
# ge�dert werden sollen oder Ihre Linux-Distribution eine Gruppe
# voraussetzt.
#
# "FaxReceiveGroup" is the group when c2faxrecv is run.
# Here it is a good idea to enter a value other than the hylafax default
# value "uucp", for instance, if the rights of /dev/capi20 are not to be
# changed or your Linux distribution requires another group.
#
# default ""
#
FaxReceiveGroup: dialout
# Im "LogFile" werden Informationen ber den Faxablauf abgespeichert.
#
# Information about the order of events in faxing are saved in the "LogFile".
#
# default ""
#
LogFile: /var/spool/fax/log/capifax.log
# Der Befehl "LogTraceLevel" gibt die Menge der Daten an, die in ein LogFile
# geschrieben werden. Die Spanne reicht von 0 = nichts bis 4 = vieles.
#
# The "LogTraceLevel" command indicates the amount of data written in a
# LogFile. The range goes from 0 = nothing to 4 = many.
#
# default 0
#
LogTraceLevel: 4
# "LogFileMode" sind die Angaben (mode), aufgrund derer sowohl das gerade
# erw�nte LogFile als auch die LogFiles fr HylaFAX angelegt werden.
#
# "LogFileMode" is the mode, on the basis of which both the LogFile just
# mentioned and the LogFiles for HylaFAX are generated.
#
# default 0600
#
LogFileMode: 0600
# Die geschweiften Klammern geben Anfang und Ende einer Section an.
# Jede Section darf eine oder mehrere SubSections enthalten.
# SubSubSections sind nicht erlaubt.
# Dabei enth�t die Section Angaben zu einem virtuellen Device;
# die Subsection die Angaben fr die Rufannahme jedes Controllers.
# Es k�nen beliebig viele Sections und, darin enthalten, jeweils beliebig
# viele Subsections erzeugt werden.
# Jede Section muss aber einen anderen HylafaxDeviceName erhalten;
# zus�zlich muss in jeder Subsection innerhalb einer Section ein anderer
# Controller aufgefhrt werden. Beim Stand-Alone-Betrieb ist eine Section mit
# entsprechend vielen Subsections ausreichend, da in diesem Betriebsmodus die
# virtuellen DeviceNamen keine Rolle spielen.
#
# The curved brackets indicate the beginning and end of a section.
# Each section may contain one or more subsections.
# SubSubSections are not permitted.
# The section contains information about a virtual device; the subsection the
# call acceptance information for each controller.
# Any number of sections containing any number of subsections may be
# generated, but each section must receive a different HylafaxDeviceName; and
# a different controller must be listed in every subsection within a section.
# For stand-alone operation, it is sufficient to have just one section with
# as many subsections as required, since virtual DeviceNames do not play
# any role in this mode of operation.
#
{
# "HylafaxDeviceName" ist der Name, unter dem sich C4H bei HylaFAX als
# "virtuelles Modem" anmeldet. Sollen fr HylaFAX mehrere dieser "Modems"
# erzeugt werden, legen Sie einfach eine neue Section mit einem anderen
# HylafaxDeviceName an.
#
# "HylafaxDeviceName" is the name, under which C4H registers in HylaFAX
as # a "virtual modem". If multiple "modems" are to be generated for
HylaFAX, # simply create a new section with another HylafaxDeviceName.
#
# default faxCAPI
#
HylafaxDeviceName: faxCAPI
# "RecvFileMode" ist der Mode, in dem empfangene Faxe abgespeichert
# werden. User und Group der Datei wird durch FaxReceiveUser (s.o.)
# festgelegt.
#
# "RecvFileMode" is the mode, in which received faxes are saved. User and
# Group of the file are determined by the FaxReceiveUser (see above).
#
# default 0600
#
RecvFileMode: 0600
# "FAXNumber" ist die eigene Nummer des Computers und wird der Gegenseite
# mitgeteilt (sichtbar z. B. im Fax-Journal).
#
# "FAXNumber" is the fax number of the computer itself and is transmitted
# to the remote site (visible in the Fax Journal).
#
# default ""
#
FAXNumber: "+351 218487755"
# "LocalIdentifier" ist der von CAPI aus konfigurierbare Teil der
# Kopfzeile. Ein leerer Eintrag fhrt dazu, dass keine Fax-Kopfzeile
# eingefgt wird.
#
# "LocalIdentifier" is the part of the fax header which can be configured
# from CAPI. An empty entry specifies an empty header.
#
# default ""
#
LocalIdentifier: "www.arcadia.pt"
# Die maximale Anzahl von gleichzeitig empfangbaren Faxen kann
# durch "MaxConcurrentRecvs" angepa� werden. Diese Anzahl wird
# durch die Anzahl der durch die Hardware zur Verfgung
# gestellten B-Kan�e begrenzt.
#
# The maximum number of faxes that can be received at the same
# time can be adjusted using "MaxConcurrentRecvs". This number
# is limited by the number of B channels provided by the hardware.
#
# default 2
#
MaxConcurrentRecvs: 2
# ----------- outgoing params -----------
# "OutgoingController" gibt den Controller an, ber den eine externe
# Verbindung aufgebaut werden soll.
#
# "OutgoingController" indicates the controller which is to be used to
# establish an external connection.
#
# default 1
#
OutgoingController: 1
# Die "OutgoingMSN" ist die MSN, die fr ausgehenden Faxe benutzt wird.
#
# The "OutgoingMSN" is the MSN used for outgoing faxes.
#
# default ""
#
OutgoingMSN: 218487755
# CLIR (Rufnummernunterdrckung) kann ber "SuppressMSN" und den Wert (0)
# abgeschaltet oder mit dem Wert (1) erneut angeschaltet werden.
#
# CLIR (Calling Line Identification Restriction) can be switched off
using # the value (0) or switched back on by entering the value (1).
#
# default 0
#
SuppressMSN: 0
# "NumberPrefix" wird vor jede Telefonnummer gestellt. Dies ist bei
# Nebenstellenanlagen wichtig, bei denen fr den Aufbau einer externen
# Verbindung eine Ziffer vorgew�lt werden muss.
#
# "NumberPrefix" is set to precede each telephone number. This is
# important for PBX systems which require that a number be dialed to
# obtain an outside line.
#
# default ""
#
NumberPrefix:
# Wenn der Wert in "UseISDNFaxService" = 1 ist, wird ein ausgehender Ruf
# mit der ISDN-FAX-G3 Dienstekennung aufgebaut. Bei 0 wird eine 3.1kHz
# Audio-Verbindung hergestellt.
#
# When in "UseISDNFaxService" the value is = 1, an outoing call will be
# established using the ISDN-FAX-G3 service indicator. For 0, a 3.1kHz
# audio connection is established.
#
# default 0
#
UseISDNFaxService: 0
# Gibt die Dauer in Sekunden an, die auf eine Verbindungsannahme durch
die # Gegenseite gewartet wird. So wird beim Faxversand nicht automatisch
die # gesamte von der Telekom vorgegebene Wartezeit genutzt. Eine Angabe des
# Wertes 0 nutzt die gesamte Wartezeit.
#
# The duration in seconds you wait for the remote site to accept your
# outgoing call In this way you do not have to use the entire ringing
# duration preset by the telephone company. The default value 0 uses the
# entire ringing duration.
#
# default 0
#
RingingDuration: 0
# ----------- incoming params -----------
{
# Controller, fr den diese Subsection gilt.
#
# Controller for which this subsection is valid.
#
# default 1
#
Controller: 1
# Wenn "AcceptSpeech" auf 1 steht, wird auch die Dienstekennung
# "Sprache" angenommen.
#
# If "AcceptSpeech" is set to 1, the service indicator "Voice" also
# will be accepted.
#
# default 0
#
AcceptSpeech: 0
# Sofern man DDI nutzen will, sollte man "UseDDI" auf 1 stellen.
#
# If DDI is to be used, "UseDDI" should be set to a value of 1.
#
# default 0
#
UseDDI: 1
# Die DDI-Stammnummer wird bei "DDIOffset" eingetragen.
# Der Standardwert fhrt zu keinem korrekten Ergebnis und
# sollte, sofern "UseDDI" auf 1 gestellt wurde, immer
# ver�dert werden.
#
# "DDIOffset" indicates the DDI offset number which precedes
# extension number. Because the default value can't guarantee
# a correct result, this value should be modified whenever
# "UseDDI" is set to 1.
#
# default ""
#
DDIOffset:
# "DDILength" gibt die Anzahl der Durchwahlziffern an. (Diese Ziffern
# werden lediglich als Teil der Empf�gernummer mitgeteilt.) Der
# Standardwert sollte bei Verwendung von DDI ebenfalls angepasst
# werden.
#
# "DDILength" indicates the number of digits in the extension. (These
# numbers are only used as a component of the recipient's number.)
The # default value should be adapted whenever DDI is used.
#
# default 0
#
DDILength:
# Bei "IncomingDDIs" k�nen in einer durch Komma getrennten Liste alle
# Durchwahlziffern (DDIs) angegeben werden, fr die Rufe angenommen
# werden sollen. Eine Bereichsangabe ist auch m�lich (z.B. 100-300),
# wobei aber keine offenen Bereiche (z.B. -100) erlaubt sind.
# Sofern IncommingDDIs gesetzt ist, wird DDILength ignoriert.
#
# In "IncomingDDIs", all extension numbers (DDIs) for which calls are
# to be accepted may be listed, separated by commas. It is also
# possible to specify a range (e.g. 100-300); here no open ranges are
# permitted (e.g. -100). When the "IncomingDDIs" switch is set, the
# parameters for DDILength will be ignored.
#
# default ""
#
IncomingDDIs:
# Bei "IncomingMSNs" k�nen in einer durch Komma getrennten Liste alle
# MSNs angegeben werden, fr die Rufe angenommen werden sollen. Ist
# die Liste leer, werden alle Rufe auf ISDN FAX G3, 3,1kHz Audio und
# eventuell "Sprache" angenommen.
# Wenn "UseDDI" auf 1 gestellt ist, wird "IncomingMSNs" ignoriert.
#
# In "IncomingMSNs", all MSNs for which calls are to be accepted may
# be listed, separated by commas. When the list is empty, all calls
# are accepted for ISDN FAX G3, 3,1kHz audio and perhaps "Voice".
# When "UseDDI" is set to 1, "IncomingMSNs" is ignored.
#
# default ""
#
IncomingMSNs: 218487754, 218487756
# Wenn "AcceptGlobalCall" auf 1 steht, werden auch Calls ohne
# Zielrufnummer (ohne MSN) angenommen.
# Notwendig hinter einigen Telefonanlagen, die keine Zielrufnummer
# senden.
#
# If "AcceptGlobalCall" is set to 1, calls without Called Party
# Number also will be accepted.
# Needed on internal ports of some PBX.
#
# default 1
#
AcceptGlobalCall: 0
QualifyTSI: "/var/spool/fax/etc/tsi"
RingsBeforeAnswer: 3
}
}
-------------------------------------------------------
With the line
QualifyTSI: "/var/spool/fax/etc/tsi"
I'm trying to filter the incoming faxes, rejecting the TSI from which I
don't want to receive faxes and accepting those I want, but I'm having
no success. I've also tried with QualifyCID and QualifyCNAME.
Any ideas ?
Regards
Lívio Cipriano
More information about the linux-avmb1
mailing list