linux-l: Netzwerk Konfiguration
Johannes Walther
hannes at walther.in-berlin.de
Di Aug 5 19:06:34 CEST 1997
Hi Leute,
ich brauch nochmal ne hilfestellung in Sachen NEtzwerk:
Es gibt einen Rechner der zwei Netzwerkkraten hat. Diese sind richtig
konfiguriert (denk ich, es ging ja mal) und werden beim Booten auch von
LILO eingetragen. Das ist auch an den Einträgen in /proc/interrupt usw.
zu sehen.
Nun kommt beim booten an der Stelle wio die rc.inet1 ausgeführt wird
eine meldung die da lautet:
"blabla:" eth0: Setting Rx mode to 1 adresses
"blabla:" eth1: Setting Rx mode to 0 adresses
"blabla:" eth1: Setting Rx mode to 1 adresses
--- seit dem komm ich nicht mehr aus der Netzkarte zum eth1 ...
In rc.inet1 steht
#-----------rc.inet1---------------
HOSTNAME='hostname'
/sbin/ifconfig lo 127.0.0.1
/sbin/route add -net 127.0.0.0
/sbin/ifconfig eth0 192.168.20.214 broadcast 192.168.20.248
/sbin/ifconfig eth1 10.100.64.100 broadcast 10.255.255.255
/sbin/route add -net 192.168.20.208 netmask 192.168.20.248
/sbin/route add -host 192.168.20.213
/sbin/route add -net 10.0.0.0
/sbin/route add default eth1
#----------ende--------------------
mit ifconfig werden beide eth0 und eth1 angezeigt...
lo Link encap:Local Loopback
inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0
UP BROADCAST LOOPBACK RUNNING MTU:3584 Metric:1
RX packets:33842 errors:0 dropped:0 overruns:0
TX packets:33842 errors:0 dropped:0 overruns:0
eth0 Link encap:10Mbps Ethernet HWaddr 00:60:97:25:B7:26
inet addr:192.168.20.214 Bcast:192.168.20.248
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:156 errors:0 dropped:0 overruns:0
TX packets:117 errors:0 dropped:0 overruns:0
Interrupt:7 Base address:0x310
eth1 Link encap:10Mbps Ethernet HWaddr 00:60:97:25:B7:26
inet addr:10.100.64.100 Bcast:10.255.255.255 Mask:255.0.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
TX packets:0 errors:0 dropped:0 overruns:0
Interrupt:10 Base address:0x300
Scheint alles ok ...
mit route wird dann das angezeigt
Kernel routing table
Destination Gateway Genmask Flags MSS Window Use
Iface
johann.walther. * 255.255.255.255 UH 1500 0 1 eth0
193.168.20.208 * 255.255.255.248 U 1500 0 0
eth0
loopback * 255.0.0.0 U 3584 0 2
10.100.64.100 * 255.0.0.0 U 3584 0 0
eth1
default * * U 1500 0 0
eth1
hmpf, wo ist denn da der fehler.....
Kernel ist 2.0.27 .............
Hannes
--
Johannes Walther <http://walther.in-berlin.de>
BeLUG: <http://tanda.informatik.hu-berlin.de/BeLUG/>
IN-Berlin: <http://www.in-berlin.de>
Mehr Informationen über die Mailingliste linux-l