linux-l: plip

[Kai Schulz]

Liebe Liste,

ich benutze Kernel 2.2.17 und versuche am parallelen Port Drucker und PLIP
gleichzeitig hinzubekommen. Beie sind statisch im Kernel einkompiliert, dem
Parport habe ich irq 7 zugewiesen. Der Aufruf
'ifconfig plip0 ernesto pointopoint ernest up' funktioniert noch, 
doch bei 'route add ernest ' kommt die Fehlermeldung: 
'SIOCADDRT: No such device'. Hier ist ein dmesg-
Auszug:

Linux version 2.2.17 (root at ernesto) (gcc version 2.95.2 20000220 (Debian GNU/Linux)) #8 Mon Dec 11 17:15:28 CET 2000
Detected 334098 kHz processor.
Console: colour VGA+ 80x30
Calibrating delay loop... 666.83 BogoMIPS
Memory: 128140k/131008k available (900k kernel code, 416k reserved, 1512k data, 40k init)
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
CPU: Intel Celeron (Mendocino) stepping 00
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xf0750
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 131072 bhash 65536)
Starting kswapd v 1.5 
parport0: PC-style at 0x378, irq 7 [SPP,PS2,EPP]
Detected PS/2 Mouse Port.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
lp0: using parport0 (interrupt-driven).
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.13)
Sound initialization started
<Sound Blaster 16 (4.16)> at 0x220 irq 5 dma 1,5
<Sound Blaster 16> at 0x330 irq 5 dma 0
Sound initialization complete
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DTTA-350840, ATA DISK drive
hdb: TOSHIBA CD-ROM XM-6302B, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: IBM-DTTA-350840, 8063MB w/467kB Cache, CHS=1027/255/63, UDMA
hdb: ATAPI 32X CD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET3 PLIP version 2.3-parport gniibe at mri.co.jp
plip0: Parallel port at 0x378, using IRQ 7
early initialization of device plip0 is deferred
PPP: version 2.3.7 (demand dialling)
TCP compression code copyright 1989 Regents of the University of California
PPP line discipline registered.
Partition check:
 hda: hda1 hda2 hda3 hda4
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 40k freed
Adding Swap: 128516k swap-space (priority -1)
registered device ppp0

Und cat /proc/parport/0/devices liefert auch zwei EInträge, einmal lp und
dann noch plip0.

Was habe ich denn vergessen?

Danke 
Kai