[linux-l] RHL 8.0 auf nForce2-Chipsatz

[Pascal Volk]

Am Dienstag, 25. Februar 2003 16:31 schrieb Andreas Burkhardt:
> Hallole,
>
> was sagt denn 'hdparm -dcmu'?
> Was sagt denn 'ps aux'?
>
> Vielleicht schickst Du am Besten mir einfach mal die Ausgabe von
> 'dmesg'.
>
> Adele, andreaz

Hallo zusammen,

hier mal ein paar Ausgaben:

	>>hdparm -t /dev/hda<<
Timing buffered disk reads:  64 MB in 17.65 seconds =  3.63 MB/sec
Timing buffered disk reads:  64 MB in 18.40 seconds =  3.48 MB/sec
Timing buffered disk reads:  64 MB in 17.47 seconds =  3.66 MB/sec

	hdparm -t /dev/hdb
Timing buffered disk reads:  64 MB in 17.98 seconds =  3.56 MB/sec
Timing buffered disk reads:  64 MB in 17.93 seconds =  3.57 MB/sec
Timing buffered disk reads:  64 MB in 18.11 seconds =  3.53 MB/sec


	>>hdparm -cdmu<<
/dev/hda:
 multcount    = 16 (on)
 IO_support   =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  0 (off)
[root at EL-PRESIDENTE root]# hdparm -cdmu /dev/hdb

/dev/hdb:
 multcount    = 16 (on)
 IO_support   =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  0 (off)


	>>hdparm -i<<
/dev/hda:
 Model=IC35L060AVER07-0, FwRev=ER6OA46A, SerialNo=SZPTZTCW254
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
 BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, 
MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=120103200
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=yes: disabled (255) WriteCache=enabled
 Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:  2 3 4 5

/dev/hdb:
 Model=WDC WD600BB-75CAA0, FwRev=16.06V16, SerialNo=WD-WMA8F1472364
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs 
FmtGapReq }
 RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
 BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, 
MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117187500
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: device does not report version:  1 2 3 4 5


	>>dmesg<<
...
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with 
idebus=xx
PCI_IDE: unknown IDE controller on PCI bus 00 device 48, VID=10de, 
DID=0065
PCI_IDE: chipset revision 162
PCI_IDE: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: IC35L060AVER07-0, ATA DISK drive
hdb: WDC WD600BB-75CAA0, ATA DISK drive
hdc: LITE-ON LTR-12101B, ATAPI CD/DVD-ROM drive
hdd: LITEON DVD-ROM LTD122, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 120103200 sectors (61493 MB) w/1916KiB Cache, CHS=7476/255/63
hdb: setmax LBA 117231408, native  117187500
hdb: 117187500 sectors (60000 MB) w/2048KiB Cache, CHS=7294/255/63
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
 hdb: hdb1 hdb2 hdb3 hdb4
...


Hoffe die Infos helfen erst mal etwas weiter.
Ich werde den Rechner jetzt mal mit Knoppix von CD booten, um 
Vergleichswerte zu bekommen.


Gruss
Pascal